滅．燃點 - 安裝方法 Fire．Stop - Install Instruction
使用雙面膠黏貼在防護設備的內部、頂部及側面。
安裝步驟
< 一 >
首先識別對應型號，取出產品後，進行檢查，
感溫探測線是否脫落、折斷、產品結構是否完好。
以上合格後，方可使用。
< 二 >
感溫探測線是否脫落、折斷、產品結構是否完好。
以上合格後，方可使用。
< 二 >
從包裝袋中取出滅火貼片或微型滅火模塊（內置雙面膠），檢查產品是否破損。
撕開雙面膠後，一定要區分產品的正反面，
有標籤紙的為正面，無標籤紙的為反面，
然後將雙面膠黏貼在產品反面，並用力按壓。
將雙面膠片黏貼在產品的無出氣孔面，用力按壓，黏貼牢固。
< 三 >
撕開雙面膠後，一定要區分產品的正反面，
有標籤紙的為正面，無標籤紙的為反面，
然後將雙面膠黏貼在產品反面，並用力按壓。
將雙面膠片黏貼在產品的無出氣孔面，用力按壓，黏貼牢固。
< 三 >
雙面膠黏貼完畢後，觀察需要安裝的櫃體，
選擇將產品黏貼到易著火點的上方。
在黏貼前一定要做好黏貼位置的清潔工作，防止有油污、水漬等。
黏貼完畢後，用力按壓，並固定感溫探測線。
即可時刻防護，自動監測火災。
< 四 >
選擇將產品黏貼到易著火點的上方。
在黏貼前一定要做好黏貼位置的清潔工作，防止有油污、水漬等。
黏貼完畢後，用力按壓，並固定感溫探測線。
即可時刻防護，自動監測火災。
< 四 >
產品安裝完成後，還需將感溫探測線固定好，
可綁紮線上纜上或固定在箱體側面上。完成後，關閉好櫃門。
保持防護空間處於相對密閉狀態。
可綁紮線上纜上或固定在箱體側面上。完成後，關閉好櫃門。
保持防護空間處於相對密閉狀態。
Apply industrial adhesive to the interior,
top and side of the equipment to be protected
top and side of the equipment to be protected
Installation Step
< 1 >
Firstly, identify the corresponding model, take out the product,
and then inspect whether the temperature detection line has fallen off or broken,
and whether the product structure is intact.
Only after the product is qualified can it be used.
< 2 >
and then inspect whether the temperature detection line has fallen off or broken,
and whether the product structure is intact.
Only after the product is qualified can it be used.
< 2 >
Remove the fire extinguisher or micro fire extinguishing module
(with double-sided adhesive inside)
from the packaging bag and check if the product is damaged.
After tearing off the double-sided adhesive tape,
it is important to distinguish between the front and back of the product,
with labeled paper on the front and unlabeled paper on the back.
Then, apply the double-sided adhesive tape to the back of the product and press firmly.
Paste double-sided film onto the non vent surface of the product, press firmly and firmly.
< 3 >
(with double-sided adhesive inside)
from the packaging bag and check if the product is damaged.
After tearing off the double-sided adhesive tape,
it is important to distinguish between the front and back of the product,
with labeled paper on the front and unlabeled paper on the back.
Then, apply the double-sided adhesive tape to the back of the product and press firmly.
Paste double-sided film onto the non vent surface of the product, press firmly and firmly.
< 3 >
After the double-sided adhesive is pasted,
observe the cabinet body that needs to be installed and choose to
paste the product above the easily ignited point.
Before pasting, it is necessary to clean the pasting position to prevent oil stains, water stains, etc.
After pasting, press firmly and fix the temperature detection line.
It can provide constant protection and automatically monitor fires.
< 4 >
observe the cabinet body that needs to be installed and choose to
paste the product above the easily ignited point.
Before pasting, it is necessary to clean the pasting position to prevent oil stains, water stains, etc.
After pasting, press firmly and fix the temperature detection line.
It can provide constant protection and automatically monitor fires.
< 4 >
After the product installation is completed,
it is also necessary to fix the temperature detection line,
which can be tied to the cable or fixed on the side of the box.
After completion, close the cabinet door.
Maintain a relatively enclosed protective space.
it is also necessary to fix the temperature detection line,
which can be tied to the cable or fixed on the side of the box.
After completion, close the cabinet door.
Maintain a relatively enclosed protective space.